Results: 70

Color evaluation of a resin cement light polymerized by different light sources and submitted to potentially staining beverages

Introduction: The color stability of resin cements, whether dual-pre-cured or photopolymerizable, as well as the color of the dental substrate, are fundamental for the aesthetic success of ceramic restorations, since the ceramic presents a high level of translucency due to its small thickness. Objectiv...

Light curing resin cements containing iodonium salts promote suitable apical bonding of posts to radicular dentin

Abstract The aim of this study was to analyze the efficiency of experimental light-curing resin cements (ERCs) with a ternary photo-initiator system containing diphenyliodonium hexafluorphosphate (DPI) and different amines on retention of glass-fiber posts to dentin (GFP). ERCs formulations: a 1:1 mass r...

Influence of preheating and post-curing on a novel fiber-reinforced composite post material

Abstract The aim of this study was to investigate the influence of preheating and post-curing methods on diametral tensile strength (DTS), flexural strength (FS), knoop microhardness (KHN), and degree of conversion (DC) of an experimental fiber-reinforced composite (FRC). Specimens (30 wt% of 3-mm-short ...

Multiple-peak and single-peak dental curing lights comparison on the wear resistance of bulk-fill composites

Abstract: The effects of tooth brushing could affect the long-term esthetic outcome of composite restorations. This study evaluated the effect of two different emission spectrum light-curing units on the surface roughness, roughness profile, topography and microhardness of bulk-fill composites after in v...

Evaluation of long-term bond strength and selected properties of self-adhesive resin cements

Abstract This study evaluated the shear bond strength (SBS) of self-adhesive resin cements (SARCs) to dentin and their physical-chemical properties. Five commercial SARCs were evaluated [SmartCem®2 - DENTSPLY (SC2); BisCem® - Bisco (BC); SeT PP® − SDI (SeT); Relyx U100® - 3M ESPE (U100) and YCE...

Effect of different bonding protocols on degree of monomer conversion and bond strength between orthodontic brackets and enamel

Abstract The objective of the present study was to evaluate the effect of different surface treatments and polymerization protocols on the bond strength of brackets to enamel, and the degree of conversion of the bonding agents. 120 bovine crowns were embedded in acrylic resin blocks and sanded. Next, the...

Immediate effects of temporary bite-raising with light-cured orthodontic band cement on the electromyographic response of masticatory muscles

J. appl. oral sci; 26 (), 2018
Abstract Objective: To assess the immediate effects of temporary bite-raising using light-cured orthodontic band cement on the superficial masseter and anterior temporalis electromyography (EMG) activity in healthy adults. Materials and Methods: Surface EMG signals were recorded bilaterally from the su...

Structural and mechanical properties of a giomer-based bulk fill restorative in different curing conditions

J. appl. oral sci; 26 (), 2018
ABSTRACT Objective: The main goal of this study was to compare the polymerization degree of bulk-fill giomer resin cured with three different light-curing units (LCUs): a polywave third-generation (Valo); a monowave (DemiUltra: DU); and a second-generation LED (Optima 10: Opt) LCUs by using structural a...

Minimization of polymerization shrinkage effects on composite resins by the control of irradiance during the photoactivation process

J. appl. oral sci; 26 (), 2018
Abstract High levels of shrinkage stress caused by volumetric variations during the activation process are one of the main problems in the practical application of composite resins. Objective The aim of this study is to reduce the shrinkage stress and minimize the effects caused by composite resin volu...

Does laser diode irradiation improve the degree of conversion of simplified dentin bonding systems?

J. appl. oral sci; 25 (4), 2017
Abstract Simplified dentin-bonding systems are clinically employed for most adhesive procedures, and they are prone to hydrolytic degradation. Objective This study aimed to investigate the effect of laser diode irradiation on the degree of conversion (DC), water sorption (WS), and water solubility (WSB...