Results: 37

Depth of cure, mechanical properties and morphology of dual-cure bulk-Fill composites

Odovtos (En linea); 25 (1), 2023
This study evaluated selected structural and physical properties, such as degree of conversion (DC), Vickers hardness (VHN), and compression strength (CS), of three new dual-cure bulk-fill resin-based composites (RBCs; ACTIVA, HyperFIL, and Fill-Up) and compared them to those of a conventional RBC (Filte...

Acute Carpal Tunnel Syndrome due to Persistent Median Artery thrombosis: Case report

Abstract Carpal tunnel syndrome is the most common compressive neuropathy of the upper limb, affecting ~ 4% of the general population. The clinical picture is characterized by pain and, mainly, paresthesia in the median nerve territory, of insidious onset and, in the most severe cases, loss of strength a...

Evaluation of the occlusal contact area of molar dental implants comparing two different thicknesses (16 μm and 200 μm) of articulating occlusal papers and forces (200 and 250 N): a pivot in vitro study

Introduction: The goal of this pilot study was to evaluate the differences between checking occlusion on implants crowns using 16 or 200 µm thickness of articulating occlusal paper, and to compare the stained occlusal area between the groups after bite forces of 200 and 250 N. Methods: It was included 1...

Uso efectivo de los adhesivos de octava generación

Rev. ADM; 79 (5), 2022
Introducción: se realizó una revisión bibliográfica con el objetivo de conocer, analizar y comparar los diferentes tipos de adhesivos de octava generación que se encuentran en el mercado y la diferencia que existe entre cada uno. Los adhesivos universales han demostrado mejoras en su resistencia, so...

Confección de prótesis de carga inmediata mediante barras articuladas: componentes, modo de uso y longitud de la barra en función de la localización
Fabrication of immediately loaded prostheses using articulated bars: components, method of use and bar length depending on the location

En la implantología actual, la confección de prótesis de carga inmediata se ha convertido en un procedi-miento de rutina. Contar con elementos pre-formados con un correcto ajuste al implante o transepitelial so-bre el que se trabaja, minimiza el tiempo de trabajo sin renunciar a la eficiencia. En el p...

Expiration Date Effect on Mechanical and Chemical Properties of Glass Ionomer Cements

The glass ionomer cements (GICs) is a generic name given to a group of materials widely used in clinical dentistry which if used after the specified expiration date, material properties may be affected. to evaluate the Vick ers microhardness, surface morphology and the energy dispersive X-ray microanalys...

Creating Antibacterial Properties in Flowable Dental Composites by Incorporation of 3, 4-dihydropyrimidin-2(1H)-ones

ABSTRACT Objective: To investigate the antibacterial, mechanical, physical properties and water sorption of flowable dental composites containing 3,4-dihydropyrimidin-2(1H)-ones. Material and Methods: 3,4-dihydropyrimidin-2(1H)-ones was synthesized and the antibacterial activity of flowable dental comp...

Evaluation of physical and biological properties of conventional glass ionomer cements

RFO UPF; 25 (3), 2020
Objetivo: avaliar as propriedades físicas e biológicas dos cimentos de ionômero de vidro convencionais (CIVs). Metodologia: foram avaliados os seguintes CIVs: Fuji IX (GC Europe, Bélgica), Ketac Molar (3M ESPE, Estados Unidos), Maxxion R (FGM, Brasil) e Vitro Molar (Nova DFL, Brasil). O tempo de pres...

Effect of fatigue load on internal mechanical properties of the intervertebral disc

Int. j. morphol; 38 (6), 2020
SUMMARY: Lumbar disc herniation is considered to be the main pathological factor for the common clinical disease of low back pain. Biomechanical factor is an important cause of lumbar disc herniation, so it is urgent to analyze the stress/strain behavior of intervertebral disc under different loading con...

Physical properties of glass ionomer cement containing pre-reacted spherical glass fillers

Braz. dent. j; 31 (4), 2020
Abstract The aim of this study was to assess the effect of different commercial liquid phases (Ketac, Riva, and Fuji IX) and the use of spherical pre-reacted glass (SPG) fillers on cement maturation, fluoride release, compressive (CS) and biaxial flexural strength (BFS) of experimental glass ionomer ceme...